PRODUCT DATA SHEET

Product Reference Cyanoacrylate Adhesive PST15

PRODUCT DESCRIPTION

PST15 is a superfast Cyanoacrylate adhesive of high viscosity. It is designed for the bonding of materials that have relatively inactive surfaces, and is expecially suitable for bonding irregular or porous components.

APPLICATIONS BENEFITS

A general purpose grade of the superfast range. Single component adhesive
Bonds in seconds ceramics, aluminium, leather. 100% Solventless
Bonding of hardwoods and fabrics. Superfast setting.
Bonding of mild steel and other metal components. 
Overcomes acid content on plated surfaces.
High impact strength.

PERFORMANCE DATA, TYPICAL VALUES

Tensile shear strength.

Tensile strength (ASTM D2095) 30 - 35 N/mm2 (4200-5000 lbf/in2)
Tensile shear strength (ASTM D1002) 20 - 25 N/mm2 (2900-3600 lb/in2)
Impact strength (ASTM 950) 2 -2.5 N/mm2 (9-11 lb/in2)
Physical properties of liquid adhesive
Monomer Modified ethyl cyanoacrylate
Appearance Colourless
Specific gravity 1.10
Viscosity @ 25° C (Brookfield) 1400-1600 cPs
Flash point (Cleveland open cup) > 85°C
Shelf life (Stored below 25° C) 12 Months minimum
Toxicity Non-toxic

Phycical properties of cured adhesive

Refractive index (ND20) 1.46
Hardness (Rockwell) 85
Specific resistance OHM/cm 8 x 1012
Dielectric constant @ 1MHZ 3.44
Softening point 165° C
Working temperature range -60° C to + 130° C

DIRECTIONS FOR USE

Ensure surfaces are clean and dry, apply adhesive to one surface. Press surfaces together and hold for 10 seconds or as indicated below. Cure speed is rapid so exercise care when aligning. Cure performance can be enhanced if necessary, by using selected activators.

TYPICAL BONDING TIMES

Plastics 5 - 60 seconds depending on substrates.
Rubbers 2 - 20 seconds depending on substrates.
Metals (degreased) 10 - 60 seconds depending on substrates.

LIMITATIONS

Ensure surfaces are degreased prior to bonding. Ensure surfaces are close fitting.
This product is not suitable for permanent glass bonding, or applications where the bonded joint may be immersed in water.

RELATIVE HUMIDITY CONDITIONS

Where possible the working environment should have a relative humidity of 50% +.

CAUTION

Prior to use consult relevant Material Safety Data Sheet.
When continuously used local fume extraction is recommended.
Contains Cyanoacrylate Ester. Use in a well ventilated environment.
In the event of inadvertent skin bonding separate bonded skin tissue carefully by peeling apart gently with a blunt instrument. Preferably after soaking in warm soapy water.
Keep out of reach of children.

STORAGE

Store in original sealed upright container between +3° C and 20° C in a dry area out of direct sunlight. The lower the temperature the longer the ultimate shelf life, but bring to room temperature before use.

PACKAGING

Available in 20g, 50g, and 500g packs.
Other packs available upon request.

DISCLAIMER

Neither Polymer Systems Technology Limited, not their approved distributors accept any liability for loss or damage arising directly or indirectly from the use of this product. The data given is for information only and is based upon data we believe to be accurate and reliable. Before using any product it is the customers responsibility to satisfy themselves by appropriate trials that each product is suitable for their intended use. As the application and use of the product is outside the control of Polymer Systems Technology Limited, the user assumes all risk and liability whatsoever in connection herewith.
All materials supplied are subject to our standard terms and conditions of trading, a copy of which is available upon request.

FOR FURTHER INFORMATION CONTACT

Polymer Systems Technology Limited ™
Unit 2 Network 4 Cressex Business Park,
Lincoln Road, High Wycombe, Bucks. HP12 3RF
United Kingdom

Tel: + 44 (0) 1494 446610 Fax: + 44 (0) 1494 528611
Email: dww@silicone-polymers.co.uk
Website: www.superglues.co.uk